EasyClosets

EasyClosets

About
EasyClosets is the nation's premier online source of DIY organizational systems such as closets, pantries, mud-rooms and laundry rooms. Clients can design their own project using our online design tool, or ask for help from one of our professional closet designers, their help is free of charge. The panels are furniture-grade quality and each project comes with a limited lifetime warranty, for as long as you own your home. The cost? That's the good news with EasyClosets you can save up to 40% off a local closet company's offerings. Call us today at 800.910.0129, we'd be delighted to help you create your next project! Established in 1986.
Overview

Serves Parsippany, NJ

Business hours

SunClosedMon8:00 am - 6:00 pmTue8:00 am - 6:00 pmWed8:00 am - 6:00 pmThu8:00 am - 6:00 pmFri8:00 am - 6:00 pmSat9:00 am - 2:00 pm

Payment methods

This pro accepts payments via Cash, Check, Credit card, and Debit card.

Contact

+18009100129

600 Lanidex Plz, Parsippany, NJ 07054

Reviews
4.0

138 reviews

5

4

3

2

1

Joe S.

Nov 9, 2017

•From Google
I was an online customer with a very large delivery order (50+ boxes). I had used EasyClosets 3 times before for walk-in closets at my previous house. When I got to this new property I knew immediately that I would need to rebuild the master closet and EasyClosets was at the top of my list. This is an older home (built in the early 70's) and it's gone through several remodels already. Although the master closet is a "walk-in" per se it is not your typical rectangular shaped room but more like a puzzle piece with different ceiling elevations and wall cut-outs as it was essentially squeezed into an unused space in the middle of the structure even though it is still a fairly large room (the equivalent of 12'x8'). For good order's sake I did pursue the closet system available through my Costco membership. That was a real disappointment. It took them a couple of weeks to fit the initial consultation into their schedule and when the consultant arrived she was scattered and unprepared (had to ask if she could borrow my tape measure). The odd dimensions of the room obviously threw her off and then it took her several more weeks to come back with a very simplistic design that didn't meet any of our needs. Using only their most basic components (white laminate shelves, no doors, or other designer elements) the total price was $15K - ouch! I knew at that moment that I could design something far better on the EasyClosets website and save a ton of money by doing the installation myself. It's important to note that the online design tool is a little finicky. It takes time and patience. I also recommend coming up with a design, printing it out, and then studying it in the room that the system will be installed in. There are little things like pieces of trim, baseboards, light switches, outlets, windows, and door jambs that you don't think of when designing so there is a lot of tweaking to the layout that needs to occur. Dimitri Benos at EasyClosets offered their free professional design services several times but given the odd configurations of my space I knew that it would be very hard for them to do the design effectively without being in the room themselves. It's also important to think about how you use the closet and what will be going in there. Having just moved from a cold climate to a warm climate, my wife and I had to completely rethink what articles of clothing, types of shoes, etc. would be in the closet on a regular basis and what we will use the most. So we studied and tweaked our design for a couple of weeks before making a final commitment. The design tool is great from a budget standpoint because it keeps an ongoing tally of how much the system will cost so you can add or delete elements to stay on budget. After placing the order I was surprised how quickly I received a shipping notice. I ordered on a Sunday and the shipping notification was emailed Tuesday morning. I could have had the product at my house before the following weekend but we were out of town so we delayed the delivery to early the next week. The only problem we had with the delivery was with the freight company. Since my order was so large it came by freight and not UPS delivery. The freight company will only deliver to "curbside". Since it was 50+ boxes we wanted the delivery in our garage which is literally a flat 30 foot run from the curb and not some long winding driveway. Despite having made the garage completely empty, the truck driver refused to put the delivery in the garage and instead left it sitting outside. Tackling 50 heavy boxes on 2 huge pallets was no easy feat so that took several days and we are lucky it didn't rain or anyone walking by got curious and helped themselves to something. An important note on assembly. If building Ikea furniture is difficult for you then stop right there! You definitely need an element of light carpentry experience and a good set of tools to put the system together. I am a very handy guy and have a lot of experience with carpentry, plumbing, electrical, etc. So for me, assembly was very easy. And once you've put one EasyCloset system together your learning curve rises quickly. But I can see where this could be very daunting for others and hence some of the negative reviews. But this is where the savings come into play. Skilled labor is expensive. This is a do-it-yourself system for a very good reason. I designed a system using top notch components that is easily twice the "value" of the Costco system I described above and it looks like a professional installation. In fact, I have a contractor doing real work at my house (kitchen remodel) and he even asked if he could take a closer look at the closet because it's so impressive. My total cost with EasyClosets was under $10K and I am quite sure if I had use the same higher grade components with Costco it would have been $20K+ installed. Overall, I love the product and will keep coming back for more.

Christina D.

Jul 22, 2016

•From Google
I used Easy Closets to design a custom walk-in closet, after dealing with a disorganized closet for years where we only had one rod per wall -- leading to a lot of clutter and messy piles of clothes leading to frustration. We ordered our closet from EC several months ago and the closet has held up extremely well. Both my husband and I now say our closet is one of our favorite places to "escape" in our apartment. We often just go in there and stare because that is truly how happy it has made us to finally have put an end to the chaos that used to be our closet. Before using Easy Closets, we had planned to use the IKEA PAX system (still a great system if it fits your needs) but for us we found it too limiting as they only come with pre-determined wardrobe sizes. Had we gone with IKEA we would have sacrificed a few feet here and there, which with a small walk-in, every bit of space counts. Their closets are automatically 24" deep but what we liked about EC is that the standard size is only 14" deep, giving us much more room to walk around and actually use our walk in closet the way it was intended. Besides IKEA we compared costs to the new TCS system from the Container Store - gorgeous but honestly not that much different from the product EC is offering except they install it for you - as well as one of the mail coupon companies that advertise custom closet solutions and require you to schedule an appointment for a rep to measure your closet in person and try to sell you right then and there. Both these solutions were much more expensive than EC and we felt would be too much hassle. Plus we would have had to make sacrifices on some of the features we wanted because it simply would have cost too much. I compared the materials all these companies are using and even the big name companies seem to be using the same type of wood as does EC with a huge markup. What I really appreciated from the get go with Easy Closets was the online system which once you get the hang of it, is super intuitive and easy to use compared to other online designers. At first, I was a little intimidated with all the choices, so I did call for advice and Roz answered the phone. Another great thing about EC is their fast and efficient customer service. Roz continued to be our main contact throughout the ordering process, answering questions at all times of day and leaving a voicemail if she missed you. She even called to tell me she made a few improvements to our design when we made a few changes, as she knew those changes wouldn't really be possible based on our closet dimensions. I really appreciated the extra insight from someone who knows her stuff and it was half because of Roz that made us want to use EC. EC if you are reading this Roz deserves a raise! She even made sure we knew about the current advertised discount. For any reviewers who complained about not knowing you need to use a saw, it is made pretty clear on the website in the "Easy process" video that lives on their homepage. That video is super cheesy and made me laugh a bunch of times but I really related to it as the whole reason we were customizing our closet was to escape the messy clutter. Both the website and the instruction packet EC provides walks you through what to do if you have a more challenging closet such as ours - our building is old, built in the 1960's and before installing we had to remove the old shelves that were painted over (not an easy task and required a trip to Home Depot to purchase a crowbar), then spackle/fill in holes and repaint walls. You are doing all this yourself before you even start to build your custom closet. For anyone wondering if the previous reviews are true, do count on receiving at least 25 boxes. The packaging center wastes a lot of cardboard (recyclable but still) and can definitely fit a few more pieces together but we didn't have any damaged items. Roz even helped us set up freight delivery given we live in an apartment building and to receive 30 boxes by UPS would have been a little strange. We were missing one of the extra accessories we ordered and Roz and team shipped it out to us the next day. They even re-shipped one of the shelving units that chipped off during the initial installation process. We have another small hallway closet that we are considering doing through Easy Closets and we would recommend them to anyone. The "easy" part is relative to your walls but we are confident had we gone with one of the professional install companies they would not have done as thorough of a job in navigating around our wall's problem areas as we did so there is a lot that goes into projects that you DIY. We hope this review helps anyone who is thinking about this system - do it. And thanks again Roz and Easy Closets for helping us to transform our master walk-in closet - it is night and day compared to the old system we had. I am posting images to show the end product.

Al H.

Feb 11, 2018

•From Google
We finally decided to redo our master closet while doing some painting. Our house is only ten years old, but I originally put in "temporary" wire shelves until I could do it up right. 10 years later... This will be a LONG post, but I want to share some installation tips. I was impressed with the flexibility of the design tool. It took a little playing around to understand all the features, but it doesn't take long until one does. This was perhaps the most attractive feature. We looked at various closet kits in store and on line, but how great to be able to design down to 1/8 of an inch! I spent a lot of time on the design and got feedback from Erna at Easy Closets. She made a few tweaks and away we went. I received my boxes in less that a week. 18 packages and about 600 pounds, I'd guess. A few of the long boxes were beat up on the ends and that worried me but when I opened them, I discovered excellent packing and no harm done. We did have a cracked 5" drawer and a slightly marred draw front caused by the packing straps, but all in all very well packed. I looked over the instructions, but being a DIYer (and a "know-it-all" engineer) I pretty much dove in and figured it out myself. The instructions are good but a little confusing in spots (the cleating and where to install the draw glides) but easy enough to figure out yourself. This is not a project for the timid. It's much more complex than putting together IKEA furniture, in my opinion! My tool list included: Stud finder--but use a fine drill to really make sure (every stud!) Hacksaw Screw drivers (including an offset driver for the lowest hutch shelf) Rubber mallet Miter box--I have a power miter saw, but used my cheapie Stanley manual box to cut the rail cover right in the closet 4-foot level Drill and various drill bits--do screwing in boards by hand! A dovetail saw--a fine cut to remove baseboard behind the hutch I worked hard to standardize to 24" and 30" widths. This will allow me to trade shelves around as needed. I'm leery of wider widths as the shelves might sag (but I don't know that for sure). This meant I ended up with a couple of small section on the rear wall, but they are behind the side wall units anyway. The fabrication precision is quite remarkable. I would say well less than 1/32". Everything fit flawlessly except one cleat was a tiny bit too long (1/2 saw kerf). The hardest part of the project by far is hanging the rails so they are absolutely straight. I was surprised how crooked the wall were in my high-end home. I had to shim the rail away from the wall as much as 1/4 inch. The need for this (if you think about it) is that if the rail isn't perfectly straight and you have multiple units, when you tighten the cam shelves, this will impose a load on the verticals that will tend to pull them away or push them toward the rail. This can cause a support failure as pointed out in the instructions. What the instructions don't tell you is how to figure out where to shim the rail. The first step is to carefully mark a line showing the bottom of the rails. I used my long level. I figured the rail height so the hutch actually settled well into the carpet. I first established the end points for the rails and cut it such that the rail junction (my closet is 10' long) was over a stud. Next I temporarily hung the rail with a few loose screws. I then ran a string from rail end to rail end. I propped the ends of the string away from the rail so a 1/4" drill bit would just clear. This same distance from the string has to be maintained at each place a screw or toggle was installed. Once you get a general idea of where shims are needed, start at one end and screw into the studs. I used wood shims from the lumber yard, Use one from the top and one from the bottom so the rail doesn't tilt. Mark them and saw them off even with the top and bottom of the rail. Now that the rail is firmly fasten to the studs, recheck the clearance for the string with the drill bit. Next figure out where the verticals go and shim behind the toggles you install. The rest is easy. Getting that rails correct is more than half the work. Cleating was a bit mysterious until I thought about the geometry a bit. The cleats (the 1/3 boards the width of a shelf) are not there to hold unit up, they are there to keep it from pulling away from the wall by breaking the notches in the verticals. Short verticals must have cleats under the top shelf. I used "cabinet" screws for a much nicer finished look than regular wood screws. The cleats provide a nice finished look to the units and I plan to order more cleats such that each of my 10 compartments has a cleat under the top shelf. I installed an angle bracket (a few were supplied but I bought more) at the top and bottom of every vertical. The top one added additional insurance against pulling away from the wall and the bottom one added a little load support help. Paint them.

Matt R.

Jan 16, 2017

•From Google
This is my first Yelp review ever, but based on my experience with EasyClosets I needed to let someone know how pleased I have been with my entire experience with this company. Like many other reviews I've read, I came across EasyClosets by a simple google search as I contemplated two closet needs at my home. The first was my son's reach-in closet and the second was going to be a new master bedroom walk in closet to be constructed in the Fall/Winter of last year. After playing around with their design tool, reading reviews, checking out local custom closet companies, I decided to use my son's closet as a test run and made a modest investment with EasyClosets to try their product/system out. I designed the closet completely with their online tool and didn't use the design help with the reach-in closet. I ordered online and sure enough it shipped the next day with three day delivery. Seven boxes showed up at my home three days later, but I knew they would because they gave me a preview of the shipping labels and I could track the packages as they made their way to my home. The packaging was intense in terms of efficiency and protection of the system components. All boxes and content were clearly labeled and the instructions were indeed customized for the closet system I designed online. Again - this was a simple reach-in with basically hanging and shelving. No drawers or other fancy components as this was a basic test and a basic 9-year old's reach-in closet. That said, I was able to install the closet one night after work. I didn't have to cut any rail due to the closet dimensions and design, but suffice it to say if you are minimally handy it is an easy system to install. I was pleasantly surprised with the quality of the materials and the overall experience I had back in March/April 2016 when I installed my son's closet. Fast forward to the early fall, when we contracted with a local contractor to demolish our existing closets in our master bedroom and to break into the attic space above our one-car garage to construct the space for our master walk-in closet. It was a fairly simple construction project, but did require a building permit, engineering, etc. and took about a month from demolition to completion. Right about the time we had the engineering completed, I started my design work on the master walk-in closet with the EasyClosets design tool. I received a call from Erna Miranda, an EasyClosets design consultant who offered to help me with my design and I took her up on this free service. She was great and patient as I worked through all the thinking that goes into creating useful and efficient closets that meet our personal needs. She offered really insightful ideas and suggestions as to how to improve my space. I have sloped ceilings in the new space and little suggestions meant a lot particularly considering that the space hadn't yet been built. Once construction was complete and finished flooring installed, I verified final measurements and Erna made adjustments to the design to accommodate the new measurements and placed the order with EasyClosets just before Christmas. While my son's reach-in was a simple design, we went full-on adult with this design including pull-out ironing board, dirty clothes hamper, 11 drawers of various sizes, a valet pole, two belt racks, his and her shoe racks, and a sliding pant rack. Needless to say we had a few more boxes and the 36 boxes weighing nearly 1,200 lbs showed up on a Tuesday last week. It took me 4 hours just to take the boxes up stairs, unpack them, and take inventory of the parts. During that inventory I found that one drawer box and the pant rack was missing. I contacted my customer service rep, John Myers who was extremely helpful and immediately ordered the missing items to be shipped. I did have to cut the metal railing this time and this was a simple thing by using a jigsaw with a metal cutting blade. Literally 15 seconds to cut the rail using the jigsaw with proper blade! The specialty items were not difficult to install and I actually enjoyed the increased complexity that these parts added to the installation. I cannot stress how simple the installation is, but I can see that this wouldn't be the case if one hasn't clearly measured the space in which the closet is being installed. Some suggestions for anyone looking to purchase and install an EasyClosets system: 1. Use the design consultants (Erna Miranda was mine and she was great!) 2. Measure three times and order once. 3. Use a jigsaw with metal cutting blade if you want the rail cutting to be easy. I highly recommend this company. I've included some pictures of my new closet which we LOVE!

Justin K.

Jun 15, 2017

•From Google
This was the most frustrating product I have ever encountered. I was surprised to learn how much work was required. I'm not talking about putting things together--that I expected--rather, it was all the details that could have been done at the factory to make our experience go smoothly that somehow weren't. Despite providing our measurements, we might as well have bought the system off the shelf from a retailer since we had to cut many of the critical pieces to measure anyway. That part wasn't actually all that difficult, but it set the stage for things to come. The instructions were practically useless. At least IKEA instructions, which are universally derided as difficult to comprehend, are specific to the product they come with--these were 10 times worse. Here I had to figure it all out on my own and just refer to some vague, half-complete images of the final product and then flip back and forth through the collection of general instructions and try to hope that they were relevant to my particular situation. I can only hope that I found everything relevant because how would I know otherwise? There are several things that, if not done correctly, will void the warranty. Those tended to be particularly obscure and/or challenging-of course. We were fortunate that I have a large collection of tools and equipment that allowed me to finish this project properly. I have no idea where we'd be if I didn't. Even the suggested tool list didn't include the things that I ultimately needed. I expected that, working with a designer and providing our unique specifications, that the pieces would come cut to measure or at least labeled so that I wouldn't have to spend so much time just trying to sort everything out. The system shipped in 23 boxes. Pieces for the four different units were all mixed in together--which is fine, I understand shipping efficiencies--BUT none of the important pieces were labeled. The result is that I had to measure each piece and try to guess where it went. Some pieces were different by less than an inch, so every single thing had to be measured. I know that labeling things is possible from the factory, since all of the structurally irrelevant shelves that just hang on pins had big stickers that I had to remove. Why couldn't the cam shelves and the vertical panels--you know, the ones that I need to actually build the closet--come labeled? At least tell me which of the corresponding units they belong to. Getting those sorted alone took over an hour. I could go on and on. I can't believe that the vertical panels, upon which literally everything hangs, have to be modified to hang over screws on the mounting rail or they will FAIL. This seems like a major design flaw that could be addressed at the factory universally (I came up with a solution using a drum sanding bit on my Dremel which could easily be applied to the manufacturing process if they actually cared) rather than leaving it to the customer to figure out if modification is necessary on any given piece. Using a drill to make a hole for the screw, as they suggest, is also totally inadequate, as sometimes the piece fits halfway over a screw-head, at which point you're trying to drill into half of a board which is extremely dangerous. Or how about that the drawers have four dimple holes for screws, but the sliders have three screws. Two of the dimples are irrelevant and one of the screws has no dimple hole at all! Why didn't you just make three dimples in the correct place? I also had to guess where all the drawers and cam shelves were supposed to go. They provide you with a giant, universal chart for where every possible thing could go in every permutation and combination. It's up to you to figure out which of those configurations matches what you have and then proceed accordingly. Now do that 12 times. If you put a cam screw into the wrong hole--which you're going to do often--unscrewing it causes the laminate to flake off, leaving ugly gouges in the surface. What it all really comes down to is that the things that could have made this truly easy, and which wouldn't necessarily require much extra work on the company's end, were omitted. It's like they deliberately tried to make this MORE difficult than necessary. That's what I don't understand, and why I will tell everyone I know to avoid this product. I will say that the closet looks great now that I finally got everything up, but "easy"? Not even close! *Response to Peter M.* I know how harsh this review comes across it was not easy to write something so scathing, considering how nice it looks and how well it fits our closet. If it was called "Beautiful Closets" we'd be having a whole different conversation! It's true I didn't call the hotline, but it just never seemed like something that would actually help with the issues I had. But TBH, now that all is said and done, I would probably come back in the future because I feel like an expert now.
Is this your business?

This business hasn't been claimed yet. Claim it to manage your listing.